Garage Door Remote not Working?

 Garage Door Remote not Working?

Garage Door Remote not Working – Have you ever had to open your garage door and struggle because suddenly, the garage door opener remote stopped working, and wondered why this happened?

Your garage door remote is used often, so there is a good chance that it will not work correctly or experience various issues.

However, do not worry; all these issues are repairable; you need to find out what precisely triggered your remote to malfunction and why it is no longer working correctly.

Some of the Reason that Triggered your Remote to Malfunction

The most common problem of a remote is that it can no longer control the device it intends to maintain.

Different causes triggered the remote to malfunction, and these are repairable. Here is some reason:

The Remote Battery is Damaged

Remote battery damage may be the reason why the remote does not work.

When we look for the problem with the remote control, we need first to check it’s battery.

Many people do not know that even if you just installed a new battery, it may be defective.

Low power of the battery can cause the remote to function or not function at all.

  1. Please remove the battery of the remote and insert it again.
  2. If the remote still does not work after this, replace the battery.

Make it a habit to check the battery because no indicator can tell when the battery power will go down.

Garage Door Sensor is Blocked

After you replace the remote with a new battery, and the door still does not respond, the problem may be the garage door sensor.

The garage door sensor can found near the lower part of the garage door.

Make sure it is not covered or blocked by any dirt or debris; this will cause the signal to be interrupted.

The remote can still send a prompt to the recipient, but the door will not open, as long as something is blocking its sensor.

Door Control Wiring doesn’t Work Properly

If it still does not work, the problem may not be with the remote or the door sensor.

The problem may be in the door control wiring or on the recipient board.

You need to check the quality of the wires in the garage door. You can use the following steps:

  1. Unplug and disconnect all the wire from the motor.
  2. Reprogram the remote control and reconnect the machine to power
  3. Reconnect the control wiring to the garage door motor.
  4. Find the wall-mounted controls and then disconnect the wiring.
  5. And lastly, test your door using the door garage remote.

Button on the Garage Door’s Wall was Locked

Another common cause of door garage malfunction is the button on the garage door wall.

You may have accidentally pressed it, causing it to be locked. However, it is easy to fix.

To unlock the button, press it again.

When the door is already unlocked, Press the open button to test if it will work properly this time.

Malfunctioning GFI

Another reason why your garage door remote control will not work is due to a malfunction of the Ground Fault Interpreter (GFI).

GFI is a device that protects us from the tools we use in our home.

And like your door garage that you use every day, a malfunctioning GFI will affect its functioning.

It can be a barrier to the functioning of the door garage.

But you can quickly repair your GFI by pressing the reset button on your wall outlet connected to the garage door.

After following all the suggested troubleshooting tasks, if your garage door and garage door remote still do not work, I encourage you to call a professional garage door technician to look and inspect your system.

Through that, you can learn more about your door garage.

But if you have trouble finding one, you can always have your garage door improvement, and you can get services from repair shops in your area!

Garage Door Redevelopment?

Suppose you are a homeowner residing throughout Ottawa, Kanata, Nepean or Vanier, and you want to have your garage door redevelopment.

In that case, we can provide you with a better experience and quality services.

Garage Door Repairs FAQ

How do I fix a garage door the keeps reopening?

A garage door is programmed to travel a certain distance before it closes. If it closes before that distance has been traveled, it thinks something is wrong — and it reopens to help prevent any damage or safety risk. In cases such as this, most likely your garage door settings simply need to be adjusted.

One garage spring broke. I have 2, should I replace both?

Garage door springs should be replaced as a set. The reason is once one spring breaks, the other one is probably not far behind, especially considering how springs weaken over time. Combining a new spring with an older one will likely cause an imbalance in your garage door’s operation. If you own 2 separate garage doors and only one spring has broken, it’s strongly recommended to replace the springs on each door if their springs are around the same age. Depending on your door’s position, when a spring breaks it can cause serious injury as well as damage your opener.

How do you fix a stuck open garage door?

First, check the track for obstructions. The area around the tracks needs to be completely clear. Second, check the remote; it could be a simple battery issue. If you still face an issue, manually unlock and gently try to close the door. If you still can’t find the problem, try giving us a call.

Can I manually open my garage door?

If your garage door does not open smoothly after pulling the releasing the cord, this could mean the door is off of its track, or the springs are broken. In either case, you should avoid trying to force the door open; doing so will only cause more damage.

How hard is it really to replace a garage door?

Installing a garage door isn’t as simple as installing a regular door. More so, installing it incorrectly can be dangerous.

Related post

contact slider
close slider

    Are you a service provider looking for leads or a client looking for a service provider? Drop us a line!